Liquid, Dispensing, Pump, Bottles



Dispensing, Bottles, Flux

Solder Wick  Without Flux     DeSoldering Braid       DeSolder Wick         Un-fluxed         No Flux Solder Wick
Solder Wick, Un-Fluxed

Solder Wick, Un-Fluxed, DeSolder Braid, Without Flux, No Flux Wick
Ameritronics Offers 6 Width
of Un-Fluxed Solder Wick

Advantages of Un-Fluxed Solder Wick:  Most high-reliability institutions have become very "picky" about which fluxes they permit into their facilities to avoid quality problems from cross-mixing fluxes. A growing industry trend requires that even solder wick -- a benchtop standard -- not be "pre-fluxed". By using solder wick that is "un-fluxed", technicians can use their own flux along with an un-fluxed wick. No worry of mixing fluxes. This is even more important in PCB Rework.

 

Mixing "water soluble" fluxes with the more traditional, established rosin/resin based fluxes can cause "white residue" build-up and prevent  quality soldering between pads and chip leads. This is only one of many reasons for a growing preference for "un-fluxed wick" at the bench by technicians, engineers and quality personnel.

 

Un-Fluxed Solder Wick Table of Widths Available

Photo

Width of Braid/Wick Length of Braid/Wick 25 Pack 10 Pack 5 Pack 2 Pack Single

.02"
0.5mm
5 Feet
1.5 Meters

WUF-020-25
$40.00

$1.60 Each


WUF-020-10
$17.00

$1.70 Each

WUF-020-05
$9.00

$1.80 Each

WUF-020-02
$3.75

$1.87 Each

WUF-020-01
$2.00
$2.00 Each

.04"
1.0mm
5 Feet
1.5 Meters

WUF-040-25
$40.00

$1.60 Each


WUF-040-10
$17.00

$1.70 Each

WUF-040-05
$9.00

$1.80 Each

WUF-040-02
$3.75

$1.87 Each

WUF-040-01
$2.00
$2.00 Each

.06"
1.5mm
5 Feet
1.5 Meters

WUF-060-25
$40.00

$1.60 Each


WUF-060-10
$17.00

$1.70 Each

WUF-060-05
$9.00

$1.80 Each

WUF-060-02
$3.75

$1.87 Each

WUF-060-01
$2.00
$2.00 Each

.08"
2.0mm
5 Feet
1.5 Meters

WUF-080-25
$40.00

$1.60 Each


WUF-080-10
$17.00

$1.70 Each

WUF-080-05
$9.00

$1.80 Each

WUF-080-02
$3.75

$1.87 Each

WUF-080-01
$2.00
$2.00 Each

.10"
2.5mm
5 Feet
1.5 Meters

WUF-100-25
$40.00

$1.60 Each


WUF-100-10
$17.00

$1.70 Each

WUF-100-05
$9.00

$1.80 Each

WUF-100-02
$3.75

$1.87 Each

WUF-100-01
$2.00
$2.00 Each

.125"
3.0mm
5 Feet
1.5 Meters

WUF-125-25
$40.00

$1.60 Each


WUF-125-10
$17.00

$1.70 Each

WUF-125-05
$9.00

$1.80 Each

  WUF-125-02
  $3.75

  $1.87 Each

 WUF-125-01
  $2.00
  $2.00 Each

©1996 - 2011, 2012, 2013, 2014-2016 Ameritronics®. All rights reserved. The information and all images you receive online from Ameritronics® is protected by the copyright laws of the United States. The copyright laws prohibit any copying, redistributing, retransmitting, or repurposing of any copyright-protected material. Ameritronics® is the registered trademark property of JTI, Inc. "Zephyrtronics" and  "Zephlux" and "ZeroLead" and "Zero Balling" and "Zero Residue" and "Post Cooling" and "PostCooler" and "AirBath" and "Quatro" and "Full Metal Jacket" are the protected trademark property of JTI, Inc.

Revised for November 21, 206

Click link below to return to the top of the page
Solder Wick, Un-Fluxed

PCB, SMD, BGA Rework & Prototyping
AirBath, SMD Rework Stations, Hot Air Pencil Soldering, BGA Rework Stations, CSP Rework Stations, Preheating Systems, PCB Preheaters, Pre-Heat SMT / SMD, Low Temp Rework, SMT DeSoldering Tools, Vacuum Pickup Tools, Circuit Board Holders, PCB Fixtures, Board Cradles, Rework Solder Paste,  No-Clean Solder Paste, Low Melt® De-Solder Wire, DeSolder Wire, Hot Air Rework Stations, Fume Extractors, SMT Dental Probes, SMT-SMD Rework Kit, BGA Rework Kit, LMK Kit, BGA Re-Balling Kit, SMD Tweezers, Power Palm Plunger

How To Work With SMD's, CSP's, BGA's & QFN's
How To - BGA Alignment: How To - SMT Rework: How To - PCB Preheating, How To - BGA  & CSP Rework: How To - Quickly Solder SMD Packages Effectively: How To - CSP Alignment; How To - Lead-Free Rework; How To - SMD Removal Economical; How To - SMD Removal Professional: How To - Hot Air Pencil / AirPencil Soldering; How To - SMD Quick Chip Removal; How To - BGA Re-Balling; How To - Rework PLCC - QFP, QFN, LCC, SOIC, Sub Shielded SMD, TSOP: How To - Solder & Rework Ceramic Capacitors: How To - Solder & Rework Glass Diodes

PCB Soldering, De-Soldering
Soldering Accessories, Solder Wire, No-Clean Solder Wire,  Soldering  Wire Dispenser, Solder Paste, Lead-Free Solder Paste, Flux, Solder Paste Dispensers, LowMelt® DeSolder Wire, De-Solder Wire, Soldering Irons, Digital De-Soldering, Soldering Tips, Thru-Hole DeSoldering Tools, Desoldering Tip, Tips for Desoldering, De-Solder Wick, Smoke Extractors, Fume Extractor Filters, Carbon Activated Filters, SolderMill™, Pre-Heating Systems, Preheat Thru-Hole, PCB Pre-Heating, Flux Solvent, How To - Connector Rework; How To - PC/104 Soldering and Rework; How To - Thru-Hole / Through Hole Desolder / De-Solder; How To - Low Melt® Desolder Wire; How To- Stop Lifting Pads; How To- Desolder / De-Solder Heavy Ground Planes; How To - Lead-Free Soldering and De-Soldering; Preheaters for Lead-Free Rework and Soldering

Dispensing, Solder Paste, Liquids & Fluids
Dispensing Systems, Dispensing Syringes, Dispensing Barrels, Tapered Tips,  Blunt Needles, Stainless Steel Needles, Dispensing Needles, Industrial Needles, Dispensing Tips, Dispensing Accessories, Solder Paste in Syringe, Lead-Free Solder Paste in Syringe, Paste Rack™ Solder Paste Holder, Dispensing Supplies, Power Palm Plunger, Manual Dispensing, Automatic Dispensing

Laboratory  & Bench  Supplies & Tools
SMD Solder Paste, Lead-Free Solder Paste, Solder Wire, LowMelt®, No-Clean Flux, BGA Flux, Rework Tack Flux, Non-Flammable Flux Remover, Inspection Equipment, Magnification Equipment, Magnifying Work Light, ESD Magnifier, Pen Vac, SMT Tweezers, Fume Extraction, SMD Tweezers, PC Board Fixtures, Hot Air Tips, AirTips, Replacement Soldering Sponges, Iron Plated Soldering Tips, Art Conservation Hot Air Tools, Foam Swabs, Anti-Static Foam Swabs, Thru-Hole Brushes, LMK Rework Kits